Edge 構成ファイル リファレンス

    # IP address or DNS name of nodes.
    IP1=192.168.1.1  # Management Server, SymasLDAP, UI, ZooKeeper, Cassandra (IP address only; do not use a DNS name)
    IP2=192.168.1.2  # ZooKeeper, Cassandra (IP address only; do not use a DNS name)
    IP3=192.168.1.3  # ZooKeeper, Cassandra (IP address only; do not use a DNS name)
    IP4=192.168.1.4  # Router, Message Processor
    IP5=192.168.1.5  # Router, Message Processor
    IP6=192.168.1.6  # Qpid
    IP7=192.168.1.7  # Qpid
    IP8=192.168.1.8  # Postgres
    IP9=192.168.1.9  # Postgres
    
    # Must resolve to IP address or DNS name of host - not to 127.0.0.1 or localhost.
    HOSTIP=$(hostname -i)
    
    # Specify "y" to check that the system meets the CPU and memory requirements
    # for the component being installed. See Installation Requirements for requirements
    # for each component. The default value is "n" to disable check.
    ENABLE_SYSTEM_CHECK=n
    
    # When "hostname -i" returns multiple IP addresses,
    # set to "y", to have the installer prompt you to select the IP address to use.
    ENABLE_DYNAMIC_HOSTIP=n
    
    # Set Edge sys admin credentials.
    ADMIN_EMAIL=your@email.com
    APIGEE_ADMINPW=yourPassword    # If omitted, you are prompted for it.
    
    # Location of Edge license file.
    LICENSE_FILE=/tmp/license.txt
    
    # Management Server information.
    MSIP=$IP1    # IP or DNS name of Management Server node.
    # Specify the port the Management Server listens on for API calls.
    # APIGEE_PORT_HTTP_MS=8080    # Default is 8080.
    
    # SymasLDAP information.
    # Set to y if you are connecting to a remote LDAP server.
    # If n, Edge installs SymasLDAP when it installs the Management Server.
    USE_LDAP_REMOTE_HOST=n
    
    # If connecting to remote SymasLDAP server, specify the IP/DNS name and port.
    # LDAP_HOST=$IP1    # IP or DNS name of SymasLDAP node.
    # LDAP_PORT=10389   # Default is 10389.
    APIGEE_LDAPPW=yourLdapPassword
    
    # Specify SymasLDAP without replication, 1, or with replication, 2.
    LDAP_TYPE=1
    
    # Set only if using replication.
    # LDAP_SID=1    # Unique ID for this LDAP server.
    # LDAP_PEER=    # IP or DNS name of LDAP peer.
    
    # The Message Processor and Router pod.
    MP_POD=gateway
    
    # The name of the region, corresponding to the data center name.
    REGION=dc-1 # Use dc-1 unless installing in a
                # multi-data center environment.
    
    # If you are using region names other than dc-1, dc-2 etc, set this property to map your region
    # name to the appropriate dc-x format region name. This property is required by Management server
    # to appropriately register Cassandra data stores based on Cassandra's data centers and regions.
    REGION_MAPPING="<custom-region-1>:dc-1 <custom-region-2>:dc-2 ... <custom-region-x>:dc-x"
    
    # ZooKeeper information.
    # See table below if installing in a multi-data center environment.
    ZK_HOSTS="$IP1 $IP2 $IP3"         # IP/DNS names of all ZooKeeper nodes.
    ZK_CLIENT_HOSTS="$IP1 $IP2 $IP3"  # IP/DNS names of all ZooKeeper nodes.
    
    # Cassandra information.
    CASS_CLUSTERNAME=Apigee    # Default name is Apigee.
    
    # Space-separated IP addresses of the Cassandra hosts (previously defined; do not use DNS names)
    # Syntax is: IP_address:host_number,rack_number
    CASS_HOSTS="$IP1:1,1 $IP2:1,1 $IP3:1,1"
    
    # Set to enable Cassandra authentication.
    # CASS_AUTH=y    # The default value is n.
    # Cassandra uname/pword required if you enabled Cassandra authentication.
    # CASS_USERNAME=
    # CASS_PASSWORD=''
    
    # Postgres username and password as set when you installed Edge.
    # Default is apigee:postgres.
    PG_USER=apigee
    PG_PWD=postgres
    
    # Use to enable Postgres master-standby replication
    # when you have multiple Postgres nodes.
    # PG_MASTER=IPorDNSofNewMaster
    # PG_STANDBY=IPorDNSofOldMaster
    
    # SMTP information.
    SKIP_SMTP=n       # Skip now and configure later by specifying "y".
    SMTPHOST=smtp.gmail.com
    SMTPUSER=your@email.com
    SMTPPASSWORD=yourEmailPassword
    SMTPSSL=y
    SMTPPORT=465      # If no SSL, use a different port, such as 25.
    SMTPMAILFROM="My Company <myco@company.com>"
    
    # The following four properties are only effective for Management server:
    # Cassandra JMX uname/pword required if you enabled Cassandra JMX authentication.
    # CASS_JMX_USERNAME =
    # CASS_JMX_PASSWORD =
    
    # Cassandra JMX SSL truststore details if you have enabled SSL based JMX in Cassandra.
    # JMX Truststore file should be readable by Apigee user
    # CASS_JMX_TRUSTSTORE =
    # CASS_JMX_TRUSTSTORE_PASS =
    
    # Set up username and password to access Qpid broker's management console
    
    QPID_MGMT_USERNAME=qpid
    QPID_MGMT_PASSWORD=Apigee1234