Edge 設定檔參考資料

以下為 9 個節點邊緣的完整靜音設定檔範例 安裝。視需要編輯這個檔案。使用 -f 選項 加入 setup.sh 以加入這個檔案。設定設定檔範例 每個拓撲的特定領域，請參閱 安裝 Edge 元件。

# IP address or DNS name of nodes.
IP1=192.168.1.1  # Management Server, OpenLDAP, UI, ZooKeeper, Cassandra (IP address only; do not use a DNS name)
IP2=192.168.1.2  # ZooKeeper, Cassandra (IP address only; do not use a DNS name)
IP3=192.168.1.3  # ZooKeeper, Cassandra (IP address only; do not use a DNS name)
IP4=192.168.1.4  # Router, Message Processor
IP5=192.168.1.5  # Router, Message Processor
IP6=192.168.1.6  # Qpid
IP7=192.168.1.7  # Qpid
IP8=192.168.1.8  # Postgres
IP9=192.168.1.9  # Postgres

# Must resolve to IP address or DNS name of host - not to 127.0.0.1 or localhost.
HOSTIP=$(hostname -i)

# Specify "y" to check that the system meets the CPU and memory requirements
# for the component being installed. See Installation Requirements for requirements
# for each component. The default value is "n" to disable check.
ENABLE_SYSTEM_CHECK=n

# When "hostname -i" returns multiple IP addresses,
# set to "y", to have the installer prompt you to select the IP address to use.
ENABLE_DYNAMIC_HOSTIP=n

# Set Edge sys admin credentials.
ADMIN_EMAIL=your@email.com
APIGEE_ADMINPW=yourPassword    # If omitted, you are prompted for it.

# Location of Edge license file.
LICENSE_FILE=/tmp/license.txt

# Management Server information.
MSIP=$IP1    # IP or DNS name of Management Server node.
# Specify the port the Management Server listens on for API calls.
# APIGEE_PORT_HTTP_MS=8080    # Default is 8080.

#
# OpenLDAP information.
#
# Set to y if you are connecting to a remote LDAP server.
# If n, Edge installs OpenLDAP when it installs the Management Server.
USE_LDAP_REMOTE_HOST=n 

# If connecting to remote OpenLDAP server, specify the IP/DNS name and port.
# LDAP_HOST=$IP1    # IP or DNS name of OpenLDAP node.
# LDAP_PORT=10389   # Default is 10389.
APIGEE_LDAPPW=yourLdapPassword

# Specify OpenLDAP without replication, 1, or with replication, 2.
LDAP_TYPE=1 

# Set only if using replication.
# LDAP_SID=1    # Unique ID for this LDAP server.
# LDAP_PEER=    # IP or DNS name of LDAP peer.

# The Message Processor and Router pod.
MP_POD=gateway 

# The name of the region, corresponding to the data center name.
REGION=dc-1 # Use dc-1 unless installing in a
            # multi-data center environment.

# If you are using region names other than dc-1, dc-2 etc, set this property to map your region
# name to the appropriate dc-x format region name. This property is required by Management server
# to appropriately register Cassandra data stores based on Cassandra's data centers and regions.
REGION_MAPPING=":dc-1 :dc-2 ... :dc-x"

# ZooKeeper information.
# See table below if installing in a multi-data center environment.
ZK_HOSTS="$IP1 $IP2 $IP3"         # IP/DNS names of all ZooKeeper nodes.
ZK_CLIENT_HOSTS="$IP1 $IP2 $IP3"  # IP/DNS names of all ZooKeeper nodes.

# Cassandra information.
CASS_CLUSTERNAME=Apigee    # Default name is Apigee.

# Space-separated IP addresses of the Cassandra hosts (previously defined; do not use DNS names)
# Syntax is: IP_address:host_number,rack_number
CASS_HOSTS="$IP1:1,1 $IP2:1,1 $IP3:1,1"

# Set to enable Cassandra authentication.
# CASS_AUTH=y    # The default value is n.
# Cassandra uname/pword required if you enabled Cassandra authentication.
# CASS_USERNAME=
# CASS_PASSWORD=''

# Postgres username and password as set when you installed Edge.
# Default is apigee:postgres.
PG_USER=apigee
PG_PWD=postgres

# Use to enable Postgres master-standby replication
# when you have multiple Postgres nodes.
# PG_MASTER=IPofNewMaster
# PG_STANDBY=IPofOldMaster

# SMTP information.
SKIP_SMTP=n       # Skip now and configure later by specifying "y".
SMTPHOST=smtp.gmail.com
SMTPUSER=your@email.com
SMTPPASSWORD=yourEmailPassword
SMTPSSL=y
SMTPPORT=465      # If no SSL, use a different port, such as 25.
SMTPMAILFROM="My Company <myco@company.com>"

# The following four properties are only effective for Management server:
# Cassandra JMX uname/pword required if you enabled Cassandra JMX authentication.
# CASS_JMX_USERNAME =
# CASS_JMX_PASSWORD =

# Cassandra JMX SSL truststore details if you have enabled SSL based JMX in Cassandra.
# JMX Truststore file should be readable by Apigee user
# CASS_JMX_TRUSTSTORE =
# CASS_JMX_TRUSTSTORE_PASS =

下表包含這些屬性的其他資訊：

IP_address[:data_center_number,rack_number]

PG_MASTER=IPofNewMaster
PG_STANDBY=IPofOldMaster

除了此處列出的屬性外，您還可以設定 Apigee mTLS。 詳情請參閱「設定 Apigee mTLS」。