4.16.09.01 - Edge for Private Cloud release notes

You're viewing Apigee Edge documentation.
Go to the Apigee X documentation. info

On Monday, October 24, 2016, we released a new version of Apigee Edge for Private Cloud.

Update procedure

To update your installation, perform the following procedure:

On all Edge nodes, clean Yum repos:
> sudo yum clean all
On all Cassandra nodes, update apigee-cassandra:
>/opt/apigee/apigee-setup/bin/update.sh -c cs -f configFile

where configFile specifies the config file you used to install Edge.
On all Postgres nodes, update apigee-postgresql:
>/opt/apigee/apigee-setup/bin/update.sh -c ps -f configFile
On all Edge nodes, update edge-gateway:
>/opt/apigee/apigee-setup/bin/update.sh -c edge -f configFile
On all Edge UI nodes, update edge-ui:
>/opt/apigee/apigee-setup/bin/update.sh -c ui -f configFile

This update includes the fix for EdgeUI-675. After you perform this update, you can configure the Edge UI to allow OpenAPI specs to define requests to private IP addresses as described at Allowing the Edge UI Access to Local IP Addresses.
If you have installed Edge Monetization services only, apply the patch for DEVRT-3098:
> /opt/apigee/apigee-service/bin/apigee-service edge-mint-management-server add-missing-notification-templates -f configFile

where configFile specifies the config file you used to install Edge.

Bugs fixed

The following bugs are fixed in this release.

Note: The build number in the table specifies the earliest version of the component that contains the fix. Use that build number to determine if you already have the fix installed, or if you need to perform an update. The apigee-service utility displays the build number of the currently installed component:

/opt/apigee/apigee-service/bin/apigee-service comp version

where comp is the name of the component without the build number extension. For example:

/opt/apigee/apigee-service/bin/apigee-service apigee-setup version

or get the build number of all components:

/opt/apigee/apigee-service/bin/apigee-all version

Issue ID	Description	Build number
APIRT-1144	XML to JSON policy enhancements The XML to JSON policy has been enhanced with the following capabilities. You can configure the policy to: Treat some XML elements as arrays during conversion, which puts the values in square brackets '[ ]' in the JSON document. Strip or eliminate levels of the XML document hierarchy in the final JSON document. For more information, see XML to JSON policy	edge-gateway-4.16.09-0.0.751
APIRT-3389	Error uploading Node.js payloads over 25KB You can now upload Node.js payloads larger than 25KB.	edge-gateway-4.16.09-0.0.751
DBS-1222	Postgres not starting with error: could not open shared memory segment	apigee-postgresql-4.16.09-0.0.942
DBS-1234	Cassandra logs directory named "{T}conf_logback.logdir{" Fixed a configuration issue where a directory for the Cassandra logs was named "{T}conf_logback.logdir{".	apigee-cassandra-2.1.13-0.0.954
DEVRT-3098	Error encountered when setting up notification templates for Monetization using the UI An error is raised when setting up Monetization notification templates using the UI, as described in Set up notifications using notification templates.	edge-mint-gateway-4.16.09-0.0.561
EDGEUI-675	Allow OpenAPI specs to access private IP Addresses By default, Edge prevents OpenAPI specs from referencing private IP addresses. You can now enable access to private IP addresses as described in Allowing the Edge UI Access to Local IP Addresses.	edge-ui-4.16.09-0.0.3743

Known Issues

This release has the following known issues:

Issue ID	Description
APIRT-3364	Message Processor does DNS lookup on IPv4 and IPv6 If you have installed and enabled NSCD (Name Service Cache Daemon) you might notice that Message Processors make two DNS lookups: one for IPv4 and one for IPv6. To disable the DNS lookup on IPv6: On every Message Processor node, edit /etc/nscd.conf. Set the following property: enable-cache hosts no
DOC-1687	Due to a known package dependency conflict, the Katello agent used in Satellite Server 6 will not install properly on Apigee Edge hosts running the Qpid daemon.

Issue ID

Description

APIRT-3364

Message Processor does DNS lookup on IPv4 and IPv6

If you have installed and enabled NSCD (Name Service Cache Daemon) you might notice that Message Processors make two DNS lookups: one for IPv4 and one for IPv6.

To disable the DNS lookup on IPv6:

On every Message Processor node, edit /etc/nscd.conf.
Set the following property:

enable-cache hosts no

DOC-1687

Due to a known package dependency conflict, the Katello agent used in Satellite Server 6 will not install properly on Apigee Edge hosts running the Qpid daemon.

4.16.09.02

4.16.09